|Exam Name||:||Specialist Implementation Engineer, PowerEdge MX Modular|
|Questions and Answers||:||54 Q & A|
|Updated On||:||Click to Check Update|
|PDF Download Mirror||:||DES-4421 Brain Dump|
|Get Full Version||:||Pass4sure DES-4421 Full Version|
What is a valid option when resetting iDRAC to factory defaults?
Preserve user and network settings
Preserve network and storage settings
Preserve identity and network settings
Preserve storage and user settings
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-r740/idrac_18.104.22.168_ug/reset-idrac-and-reset-idrac-to-default?guid=guid-1b5c2d57- 05c8-4098-8344-49c984839c30&lang=en-us
What is a characteristic of MX7000 networking in Full Switch Mode?
Layer 2 bridging is disabled by default and interfaces must join a bridge domain (VLAN) before being able to forward frames.
Networking is enabled by default and all switch-specific OS10EE capabilities are available.
Networking is available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
Switches operate as layer 2 I/O aggregation devices and are managed through OME-M.
A technician is deploying a new MX7000 chassis using the Chassis Deployment Wizard. What is the correct order o steps followed by the wizard?
Select and Place:
What is a characteristic of MX7000 networking in Scalable Fabric Mode?
Enabled by default, all switch-specific OS10EE capabilities are available.
Layer 2 bridging is disabled be default and interfaces must join a bridge domain (VLAN) before being to forward frames.
All switch interfaces are assigned to VLAN 1 by default and are in the same Layer 2 bridge domain.
Available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
Which I/O module is supported for Fabric B?
A company has several MX7000-systems, four FX2 solutions, one M1000e, and several PowerEdge rack servers. Which management interface is recommended for managing this range of systems?
OpenManage Modular, no optional plugins required
OpenManage Modular with optional plugins
An administrator is about to perform a firmware update on an MX9116n switch OS 10 from the CLI. The latest OS 10 switch firmware image has been downloaded and their TFTP server is set up.
Upon logged in with administrator credentials on the switch, which command should be used to start the update procedure?
What is the number of server-facing ports and the bandwidth of each port on the MXG610s? (Choose two.)
8x 16 Gbps
16x 32 Gbps
16x 16 Gbps
8x 32 Gbps
Reference: https://i.dell.com/sites/csdocuments/Product_Docs/en/DellEMCNetworkingMXG610sSpecSheet.pdf (page 1)
What can be used as the firmware update source for OME-M within an MX chassis?
Server Update UtilityBaseline from a Catalog
Server Update Utility
System Live Image (SLI)
Dell Update package
System Live Image (SLI)
Dell Update PackageBaseline from a Catalog
A new administrator has just taken over an MX7000 Multi-Chassis Management Group and two-racks of PowerEdge servers. The previous administrator no longer works at the company and is not available. No one knows the password for the OME-M interface and the default password is not working.
What must be used to reset the password?
iDRAC for one of the compute sleds.
Left ear control panel.
RACADM using a serial connection
Management Module jumpers
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-mx7000/omem1.00.01_ug/recovering-passwords?guid=guid-553bf2dd-c491-4117-85f5- c2fbfde4ef12&lang=en-us
A server sled has a single mezzanine card installed in the correctly supported slot. To which IOM fabric(s) does the sled have access?
Fabric A1 and Fabric A2
Fabric A1 only
Either Fabric A or Fabric B, depending on the configuration set in OME-M
Fabric A1 and Fabric B1
When performing "A1 the Box" management, what must be done to successfully connect to the Management Module?
Configure PuTTY for a serial connection
Change the baud rate to 128000
Connect cables to the KVM
Attach standard A-to-A USB cable to a laptop