|Exam Name||:||Delta-Aruba Certified Switching Professional|
|Questions and Answers||:||40 Q & A|
|Updated On||:||Click to Check Update|
|PDF Download Mirror||:||HPE6-A46 Brain Dump|
|Get Full Version||:||Pass4sure HPE6-A46 Full Version|
Refer to the exhibits. Exhibit 1.
The exhibits show the current operational state for routes on Switch-3. The company wants Switch-3 to prefer the link to Switch-1 over the link to Switch-2 for all intra-area, inter-area, and external traffic.
What can the network administrator do to achieve this goal?
A . Set the OSPF cost on VLAN 108 higher than 1 on Switch-2 and Switch-3. B . Set the OSPF administrative distance on Switch-2 higher than 110.
C . Set the OSPF area type to normal on all of the switches in Area 1.
D . Set the cost in the OSPF Area 1 stub command higher than 1 on Switch-2.
Refer to the exhibits. Exhibit 1.
The VoIP phone connects, authenticates successfully, and is dynamically assigned to tagged VLAN 6. The endpoint connected to the phone does not authenticate but starts to send untagged traffic.
How does the switch handle this traffic? A . It forwards the traffic in VLAN 5.
B . It relays the traffic to the RADIUS server for authentication. C . It forwards the traffic in VLAN 6.
D . It drops the traffic.
Answer: B Question: 34 Refer to the exhibit.
A network administrator sets up prioritization for an application that runs between Device 1 and Device 2. However, the QoS for the application is not what the administrator expects.
How can the administrator check if the network infrastructure prioritizes traffic from Device 1 and Device 2?
A . Run a packet capture on Device 2, run the application, and look in the packet capture for a high value DSCP in the
B . Set up RMON alarms on the switches that trigger when a high number of packets are dropped. Then, run the application and check for the alarm.
C . Clear interface statistics on the switches. Then, run the application and check the interface queue statistics for the switch-to-switch links.
D . Run a packet capture on Device 1, run the application, and look in the packet capture for a high value DSCP in the IP header.
Answer: A Question: 35 Refer to the exhibit.
An AOS-Switch has an extended ACL that is applied to several physical interfaces.
New interfaces have been brought online.
The ACL has been applied to them as well.
A network administrator sees the output in the exhibit and is concerned that the switch will reach the limit for rules. What can the administrator do to address this concern?
A . Resequence the ACL with less space in between the entries. B . Enable ACL grouping, and apply ACLs as shared ACLs.
C . Reconfigure the ACL as a standard ACL, and then reapply it.
D . Remove static ACLs, and have the RADIUS server send dynamic ACLs.
Answer: A Question: 36 Refer to the exhibit.
A company requires distribution layer switches that can provide Layer 2 and Layer 3 redundancy. The exhibit shows the proposal for these switches.
Which change to the proposal will help meet the company’s requirements?
A . The proposed switches should be replaced with switches such as the Aruba 2930M to support the backplane stacking technology.
B . VRRP should be implemented instead of backplane stacking to support the Layer 3 redundancy requirements. C . Link aggregations should be established without LACP to support the Layer 2 redundancy requirements and backplane stacking limitations.
D . The proposed switches should be replaced with switches that support VSF to support the required distance between stack members.
Answer: C Question: 37 Refer to the exhibit.
The network administrator enables DHCP snooping globally and on VLAN 2. An additional step is mandatory for DHCP snooping to operate correctly and for clients to receive DHCP settings.
What is the additional mandatory step? A . Define trk1 as a trusted DHCP port. B . Define an authorized DHCP server. C . Enable ARP protection.
D . Define edge ports as untrusted DHCP ports.
An AOS-Switch enforces 802.1X. It receives an Access-Accept with this HPE VSA from its Radius server: Attribute Name and ID = HPE-User-Role (25) Value = contractor
The switch then rejects the client.
What is one requirement for the switch to accept the message and authorize the client? A . The initial user role must be set to the factory default permit any role.
B . User role authorization must be enabled globally on the switch.
C . An aaa authentication local user group must have the contractor name. D . The RADIUS server settings must permit dynamic authorization.
A network administrator needs to create a backplane stack with four AOS-Switches. The administrator wants to choose which switch becomes the commander.
Which procedure meets those needs?
A . Boot all of the switches at the same time and then connect the backplane stacking links. Then, access the desired commander, and make sure it has member ID 1.
B . Configure backplane switches settings on each switch while disconnected. Make sure the desired commander has priority value 1. Then, connect the switches.
C . Boot up the desired commander first and make sure stacking is enabled on it. Then, connect the stacking links and boot the other switches.
D . Configure backplane switching settings on each switch while disconnected. Make sure the desired commander has member ID 1. Then, connect the switches.